Get inspired

Subscribe to our Newsletter for news on latest products and sales


    Janson Pottery

    How to make a coil pot

    Coiling is perhaps the most versatile of the hand building techniques, because it allows you to build forms of any design or scale. It’s generally considered to be a slow and contemplative way of working, which demands patience and attention to detail more than anything else. There are several methods of using coils but in this coiling project we will use the traditional method of rolled coils, and expand on other techniques in future issues until you find the method most suited to you.

    The right clay – tips
    Clay used for coiling must be plastic, to prevent it cracking as you build the form – your pottery supplier will be able to advise on the best type of clay to meet your needs, but generally:

    • Adding 20-30% grog or sand to your clay will increase its strength.
    • The bigger the item to be built, the groggier the clay should be.
    •Smooth clays like porcelain are much harder to coil, with so only use these for small items that can be built relatively quickly. A better choice would be a stoneware body. 

    What you need to begin

    Scraping tools with different rounded edges are especially good for the insides of pots where there may be angles that are hard to get to.
    Loop tools are also really useful for removing large amounts of excess clay to reduce the thickness of the clay wall – a loop which is rounded at one end and pointed at the other is the best choice for the inside of larger coiled pots.
    Surform blade tool
    Board to work on


    Getting started – outline formers / templates
    Before you start to build your coil pot you should know what shape you intend to build – this sounds an obvious point to make but students often start to coil with no real idea of this, and the shape of the pots looks unresolved as a result.

    If you want to be precise in this process, the next step would be to make an outline former because this will help you keep control of the shape as you build it.

    The best material to use for the former from is thin MDF, which can easily be cut with a strong knife, but thick cardboard or hardboard will also work well.

    Things to bear in mind when making a former:
    • The board must be large enough to allow you to hold it comfortably when in use. Make allowances for the size of your hand by gripping the side of the board before drawing and cutting out the shape.
    • Draw the outline shape with a black marker pen – it’s easier to see than a pencil line when cutting out.
    • The board must have a level base so that it can sit on the board that the pot’s made on to keep the shape true.


    Coiling 1
    Begin by forming the clay into a thick sausage shape in both hands. You can actually thin the coil quite considerably this way, but only do this until it becomes difficult to handle.


    Coiling 2

    Roll your coil on a non-absorbent surface – melamine is good if you have some, but whatever you roll on it’s important that the coils don’t lose moisture at this stage.

    Roll with the palms of the hands, rather than the fingers which will make marks in the clay. Start in the middle and work outwards, rolling the clay back and forwards until it’s a thickness you’re happy to work with. A 10 mm thickness is about right to start with.


    Coiling 3

    Roll several coils to ensure you can build your pot in one go, without having to stop to make more. Keep the rolled coils on plastic sheeting and cover with more plastic until ready to use, to prevent moisture loss.


    Coiling 4

    Cut the base from a soft, rolled or pinched slab of clay using a pastry cutter to make an accurate disc. Make the base a little larger than required because some size will be lost when the first coil is attached.


    Coiling 5

    Create a foot ring by placing a small disc on the underside of the base slab. The disc can be purpose-made from bisque-fired clay, or you could use a large coin, flat button or thick card. Turn the base over and place on a board –leaving the disc in place underneath.


    Coiling 6

    Attached the first coil, after scoring and slipping the edge of the base section. This will be periodically necessary at stages as the form builds up, but only if the clay is too firm to blend easily. Begin by blending one end of the coil down onto the base carefully.


    Wind the rest of the coil around for its entire length so that it flares out gently to form a bowl shape.


    coiling 8

    Supporting the form, by cupping the side in one hand, carefully blend the coils into one another and onto the rest of the base. Blend the clay downwards using a thumb, finger or wooden tool.


    Coiling 9

    When the coil has been blended in on the inside of the form, turn it over and repeat the blending process on the outside, taking care not to squash the form. This is easier if you hold the shape in one hand as you blend with the other.


    Coiling 10

    Remove the disc from the base and very carefully refine the surface using a metal or plastic kidney to remove lumps and bumps and smooth the surface.

    At this stage you can use a wooden spatula to paddle the surface of the pot to correct the shape and help compact the clay and ease out any irregularities in the surface if you aren’t happy with the shape.


    Coiling 11

    Repeat the smoothing and blending process on the inside using a small plastic kidney to remove excess clay.


    Coiling 12

    Sit the pot on a board and make any corrections to the rim using a Surform to level it. This is worth doing periodically because it helps keep the shape and prevents distortion.


    Coiling 13

    Check the shape of your pot so far, by holding the outline former flat on the board the pot is sitting on, then drawing it carefully around the form. It will help if the board is sitting on a banding wheel to do this. Any corrections to the shape should be made as soon as they’re detected, and by doing this regularly you’ll maintain control over the pot. Score and slip the rim of the pot, then continue to build up the shape in the same way until it reaches the desired shape and height.



    Coiling 15

    Remember to make periodic checks and corrections to the shape, using the outline former to guide you.


    Coiling 15

    Thoroughly work over the surface of the pot to remove irregularities of thickness, and take special care at the rim because this is the point the eye is first drawn to. Use a kidney to minutely even-up the clay section, compact the clay, and level the rim.


    Coiling 16

    The bowl is now finished and ready for decoration and firing.